Post by darkjak87 on Jul 22, 2008 20:14:24 GMT -5
*Note: I did not create this guide. I have copied and pasted it because I believed it to be very useful, and posted it here.
1. Type "about:config" into the address bar and hit enter. Scroll down and look for the following entries:
network.http.pipelining
network.http.proxy.pipelining
network.http.pipelining.maxrequests
Normally the browser will make one request to a web page at a time. When you enable pipelining it will make several at once, which really speeds up page loading.
2. Alter the entries as follows:
Set "network.http.pipelining" to "true"
Set "network.http.proxy.pipelining" to "true"
Set "network.http.pipelining.maxrequests " to some number like 30. This means it will make 30 requests at once.
3. Lastly right-click anywhere and select New-> Integer. Name it "nglayout.initialpaint.delay" and set its value to "0".This value is the amount of time the browser waits before it acts on information it recieves.
These next few line inputs are only if you didn't notice a difference, you can put them if you want, but it wont change, I doubt you'd notice anything.
These next few are not set in the about:config by default because the browser changes them all the time by it's self, but doing this make sure they are set to the right thing all the time, so the that above will work.
1. Create a new Boolean and call it 'content.notify.ontimer' and set it to 'true'.
2. Create a new Integer and call it 'content.notify.interval' and set it to '120000'.
3. Create a new Integer and call it 'content.max.tokenizing.time' and set it to '360000'.
4. Create a new Boolean and call it 'content.interrupt.parsing' and set it to 'true'.
Now, with those in place, if you hadn't noticed a change before, you should now.
Don't set the Integers to anything else, any lower, and the page will open faster, but it will load the total content slower, any higher and it will open slower, load the content faster, but your performance will take a hit, reducing it doesn't increase your performance, before you try and loop hole it either, those 2 numbers are the 'optimum' settings for both speed and performance, where the lines on the graph cross, if you will.
Enjoy.
1. Type "about:config" into the address bar and hit enter. Scroll down and look for the following entries:
network.http.pipelining
network.http.proxy.pipelining
network.http.pipelining.maxrequests
Normally the browser will make one request to a web page at a time. When you enable pipelining it will make several at once, which really speeds up page loading.
2. Alter the entries as follows:
Set "network.http.pipelining" to "true"
Set "network.http.proxy.pipelining" to "true"
Set "network.http.pipelining.maxrequests " to some number like 30. This means it will make 30 requests at once.
3. Lastly right-click anywhere and select New-> Integer. Name it "nglayout.initialpaint.delay" and set its value to "0".This value is the amount of time the browser waits before it acts on information it recieves.
These next few line inputs are only if you didn't notice a difference, you can put them if you want, but it wont change, I doubt you'd notice anything.
These next few are not set in the about:config by default because the browser changes them all the time by it's self, but doing this make sure they are set to the right thing all the time, so the that above will work.
1. Create a new Boolean and call it 'content.notify.ontimer' and set it to 'true'.
2. Create a new Integer and call it 'content.notify.interval' and set it to '120000'.
3. Create a new Integer and call it 'content.max.tokenizing.time' and set it to '360000'.
4. Create a new Boolean and call it 'content.interrupt.parsing' and set it to 'true'.
Now, with those in place, if you hadn't noticed a change before, you should now.
Don't set the Integers to anything else, any lower, and the page will open faster, but it will load the total content slower, any higher and it will open slower, load the content faster, but your performance will take a hit, reducing it doesn't increase your performance, before you try and loop hole it either, those 2 numbers are the 'optimum' settings for both speed and performance, where the lines on the graph cross, if you will.
Enjoy.